This machine is very useful for preparation of spectro sample very fast and clean. Outer body made of thick M. Steel with powder coated rust proof paint. Disc Cover: Machine to suit the disc housing and to cover the disc plate by 180 deg. For safety Disc plate: Made of steel with air gripping arrangement to aluminium disc and with locking system to keep the aluminium disc in position. Disc Housing: made of aluminium and machined to suit the disc plate, disc covers and machine stand. At the back of the disc housing the pipeline connected to the dust-collecting unit, cooling and gripping the aluminium disc uniformly at the time of operation. Main Motor: 2 HP, 2800 RPM: 440/460 volt 3 phase AC Supply Suction Motor: 1HP, 1400 RPM Starters: Push button type of main and air gripping motor, With all standard accessories.

Model BBG-32 Belt Grinding Machine is of new generation design, made according to the international standard and advanced process technique. It adopts sand belt to grind and polish the specimen. The different belts can be changed swiftly. This machine can be used to replace the disc grinder and manual type abrasive paper grinding. It only takes 1-2 minutes to for each belt to finish the operation. For the grinding of spectroscopy specimen, it is very economic to save time, labour and abrasive paper. This machine can be widely used in laboratories, researching institutes and factories.

Belt Grinder is suitable for flat, coarse grinding prior to fine grinding. The specimens to be ground in 60, 80 or 120 grit after cutting operation or moulding to remove surface imperfections. Useful step to remove light metallurgical damage in the specimen surface induced during cut-off operation.

This Machine is Automatic Mounting Press for metallographic specimen. It is suitable for all Thermosetting Materials, because of the cooling system. It can automatically finish with the heating temperature, the holding time and acting force. The operator can change 3 specification patterns according to the different specimens. Specifications:  Pattern Specimen: Ø30  Heater Capacity: 650W, 220V  Adjustable Temperature Range: 0-150°C  Power: Single Phase, 220V, 50Hz  Cooling Method: Water Cooling  Pneumatic Pressure: 0-5 bar  Temperature: 0~150°C  Dimension: 730 x 570 x 460 mm  Weight: 45 Kg

This Machine is Automatic Mounting Press for metallographic specimen. It is suitable for all Thermosetting Materials, because of the cooling system. It can automatically finish with the heating temperature, the holding time and acting force. The operator can change 4 specification patterns according to the difficult specimens. It can make 2 specimens at one time.

Model MBP-1B Metallography specimen grinding & polishing machine is equipped with single disk and features stepless speed changing grinding and polishing. The rotating speed of grinding and polishing disk is adjustable from 50 to 1280 rpm. It can realize the whole process of rough grinding, fine grinding, rough polishing and finishing polishing for specimen preparing. This machine features easy operation and economical applying. It is the ideal specimen preparing instrument for using in factories, scientific research institutes and laboratories of colleges.

This is a mechanical type machine. By turning the hand-wheel of the machine, a couple of bevel gear is rotated to drive the screw rod which in turn pushes/pulls the lower die up and down along the mould sleeve. The thermo set plastics together with specimen being mounted is formed under heated conditions. During this process the pressure is self adjusted by a spring fixed inside the machine. A Signal light is used to indicate the pressure level.

Metallography specimen polishing machine with variable rotating speed, having digital display RPM meter to indicate the speed of both rotating disks in revolution per minute. It is a kind of double ¬disk table type polishing machine and can be operated by two persons at the same time. It is suitable for the polishing & grinding of the specimen. The specimen surface is very smooth after processing and can be used to observe and measure the metallography structure of specimen under microscope.

Metallography specimen polishing machine with variable rotating speed is suitable for the polishing of the specimen which has been grinded. The specimen surface is very smooth after processing and can be used to observe and measure the metallography structure of specimen under microscope.

Metallography specimen polishing machine is suitable for the polishing of the specimen which has been grinded. The specimen surface is very smooth after processing and can be used to observe and measure the metallography structure of specimen under microscope.